Send Inquiry x
I can help you
Send

5454 Aluminium Coil Strip

Current Position :Home/Alloy Strip Coil/5454 Aluminium Coil Strip

5454 Aluminium Coil Strip Introduction
5454 Flat Aluminium Strip / Flat Aluminum Strips in China

 
    Aluminum alloys contain strong corrosion resistance. These alloys are good low-temperature alloys. Aluminium / Aluminum alloys are sensitive to high temperatures ranging between 200 and 250°C (392 and 482°F). The strength of these alloys increases when exposed to subzero temperatures and the strength decreases when exposed to high temperatures.

Chemical Properties - 
5454 Aluminium Coil Strip

Alloy Designation Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Remarks Others Aluminium
min
Numerical Chemical Sympols Each Total
EN AW
-5454
EN AW-
AI Mg3Mn
0.25 0.4 0.1 0.5-1.0 2.4-3.0 0.05-0.2 - 0.25 0.2 - - - 0.05 0.15 Remainder

Mechanical Properties - 5454 Aluminium Coil Strip






The following datasheet provides an overview of Aluminium / Aluminum 5454 alloy.
 
Physical Properties - 
5454 Aluminium Coil Strip
The following table shows the physical properties of Aluminium / Aluminum 5454 alloy.

Properties Metric Imperial
Density 2.6-2.8 g/cm3 0.0939-0.1011 lb/in3
Melting point 607°C 1125°F

Thermal Properties - 5454 Aluminium Coil Strip
The thermal properties of Aluminium / Aluminum 5454 alloy are given in the following table.

Properties Conditions
T (ºC) Treatment
Thermal conductivity 134 (W/mK) 25 All
Fabrication and Heat Treatment
 
Annealing
Aluminium / Aluminum 5454 alloy is annealed at 343°C (650°F) only when the need to relieve the cold working stress arises. After being sufficiently heated the alloy is finally cooled in air.
 
Cold Working
Aluminium / Aluminum 5454 alloy is capable of being cold worked by using conventional methods. This alloy can be cold worked in any of the H-32, H-34, H-111 tempers or in the annealed condition.
 
Welding
Aluminium / Aluminum 5454 alloy is capable of being welded by all the commercial welding methods.
 
Forging
Aluminium / Aluminum 5454 alloy can be hot forged.
 
Forming
Aluminium / Aluminum 5454 alloy can be readily cold worked in the annealed or tempered conditions. This alloy contains good cold working and hot working characteristics.
 
Machinability
The machinability of Aluminium / Aluminum 5454 alloy is rated from fair to poor. Machining operations for this alloy is recommended when the alloy is in the H-34 temper condition. Oil lubricants can be used in the machining process.
 
Heat Treatment
Aluminium / Aluminum 5454 alloy cannot be heat treated.
 
Hot Working
Aluminium / Aluminum 5454 alloy can be hot worked in the temperature range of 371 to 204°C (700 to 400°F).
 
Hardening
Aluminium / Aluminum 5454 alloy can be hardened only by being cold worked.
 
Applications
Aluminium / Aluminum 5454 alloy is used in pressure vessels, marine service and welded structures.


 


CONTACT US
Contact
联系我们
Looking Forward to Your Response!

Tel:037155689814

Phone:13673369503

Fax:+86-371-55686475

Mobile:13673369503

Skype:signialuminium

Email:frank@signialuminium.com

Address:A126 Building 4, No.89 Science Avenue,National HI-Tech Industry Development Zone,Zhengzhou,Henan

[UP]